On Sale
NixTrainz NixTrainz | Decoder Buddy Mini (1k Ohm Resistors Onboard)
The Decoder Buddy Mini was developed to fit into smaller steam and diesel applications. there has also been interest in HOn3 and S-Gauge applications. This mother board does not include the 21 Pin Decoder. This mother board requires soldering. These printed circuit board is NOT INTENDED FOR USE IN A DC SYSTEM. The mother board includes: One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One set of stay alive pads (U+ , GND and if necessary a third control wire ) One pair of speaker pads Resistors for use with LED lighting. (Also available with 0 ohm, 750 ohm and custom specified resistors for function outputs. This accommodates some previously installed and "12 volt LEDs".) It is IMPORTANT to realize that resistors must be used when LEDs are connected to the four lighting outputs of the Mini!!! The resistors may be soldered in line when purchased or the included resistors may be soldered inline upon installation. Remember there are different incandescent lamp voltage requirements and current draw that have to be taken into consideration also. (Until the next batch is produced the Mini will be labeled Tiny and the picture on the package will indicate the correct headlight outputs for direction of locomotive.)
$10.99$9.89
Woodland Scenics Woodland Scenics 619 | Static Grass Light Green 4mm
Static Grass 42 grams Grass length: 4mm
$4.49$4.04
Train Control Systems Train Control Systems (TCS) 1694 | WOWSpeaker 28mm High Bass Round 4W | Multi Scale
You haven’t heard WOWSound until you’ve heard it through our 28mm High Bass 4W WOWSpeaker! This speaker handles an unprecedented 4 watts of power, and showcases a mighty bass reflex that packs a big sonic punch. Welcome to the new standard for sound in model trains – pick one up today and prepare to be blown away! This speaker is 28mm (1.1″) diameter and 13.5mm (0.53″) thick which includes a rubberized mounting gasket. The mounting gasket allows for unrestricted movement of the cone, preventing distortion or physical damage! Note: Product listing is for 1x speaker. Additional images provided for clarity. Dimensions: 1.1″ diameter x 0.53″ or 28mm diameter x 13.5mm Sound Pressure Level: 84 ± 3.0 dB (A), at 0.63 V, 0.1 m, Average 500,1,000, 2,000, 4,000 (Hz ), at 25°C Effective Frequency Band: 250 Hz. to 20 kHz. Power Rating: 3W (Typical) 4W (Peak) DC Impedance: 4 Ω ; ± 15%, at 1,000 Hz., 1.0 V
$13.79$12.41
Woodland Scenics Woodland Scenics 621 | Static Grass Dark Green 7mm
Static Grass 42 grams Grass length: 7mm
$4.49$4.04
Woodland Scenics Woodland Scenics 644 | Static-Tac® | Multi Scale
Static-Tac is specially formulated and has the right viscosity for adhering Static Grass and Briar Patch. It comes in a bottle with a graduated tip that works for large or small areas. Static-Tac is an easy-to-spread adhesive that dries to a clear matte finish for realistic results.
$8.39$7.55
Woodland Scenics Woodland Scenics 623 | Static Grass Light Green 7mm | Multi Scale
Static Grass 42 grams Grass length: 7mm
$4.59$4.13
Woodland Scenics Woodland Scenics 628 | Static Grass Straw 12mm | Multi Scale
Static Grass 28 grams Grass length: 12mmm
$4.49$4.04
Woodland Scenics Woodland Scenics 620 | Static Grass Straw 4mm
Static Grass 42 grams Grass length: 4mm
$4.50$4.05
Woodland Scenics Woodland Scenics 625 | Static Grass Dark Green 12mm | Multi Scale
Static Grass 28 grams Grass length: 12mmm
$4.59$4.13
Ring Engineering Ring Engineering WH-9 | RailPro Wiring Harness
Quantity: Two per packageThe WH-9 wiring harness can be used with all RailPro Locomotive modules. The WH-9 conforms to NMRA 9 pin plug standard so it can be used for any DCC locomotive where applicable. The WH-9 wiring harness can be used to add the required DCC 9 pin plug (JST) to a non-DCC locomotive. Or you can use it after removing all circuit boards from a DCC equipped or DCC ready locos (too allow a cleaner installation or make more room for a RailPro module). Please see LM instructions for actual wiring. JST connectors can come in two different ways that the pins are connected to the wires (crimp style and insulation displacement) both connect in the same manner and are interchangeable. However, we have found the crimp style pins to be far more dependable than the insulation displacement connectors that some DCC suppliers sell. WH-9 has a JST 9 pin with crimp style pins.
$6.39$5.75
Woodland Scenics Woodland Scenics 622 | Static Grass Medium Green 7mm
Static Grass 42 grams Grass length: 7mm
$4.59$4.13
Woodland Scenics Woodland Scenics 627 | Static Grass Light Green 12mm | Multi Scale
Static Grass 28 grams Grass length: 12mmm
$4.59$4.13